Rainbow components

Justin from Detroit1 · Sat Oct 21, 2006 3:10 pm

When I was a dealer for Incriminator, the dealer cost on a 12" 187 was around $50. How the hell can they charge $35??

audiobass10 · Post by **audiobass10** » Sat Oct 21, 2006 3:34 pm

Justin from Detroit wrote:When I was a dealer for Incriminator, the dealer cost on a 12" 187 was around $50. How the hell can they charge $35??

Where does it say they charge 35 bucks? There site was hacked recently..could have reflected changes in pricing. I cant even get on there right now.

William from NOLA · Post by **William from NOLA** » Sat Oct 21, 2006 3:46 pm

Is their site working for you guys? I'm getting a "not authorized" message currently.

geolemon · Post by **geolemon** » Sun Oct 22, 2006 10:35 am

GlassWolf wrote:any word on the statement 15" production?

Wish I could... Making changes, and focusing a bit more on the little sub, for better or worse. Really, we keep going back and forth, as we've got a "bigger and better" design that I'm pushing for, even though it's going to delay the release from the other option - a "release 1 / release 2" combination.

Due to some real support and enthusiasm here, I'm no doubt going to do a small "beta run" - essentially a RFP (request for prototype) that's perhaps 10 or 20 units under the guise of stress-testing for example - larger than your usual RFP.

And what might be cool with that is the "stealth" factor - usually those prototypes are mechanically exact, but with cosmetic details left out, so they could look slightly different (logo, plating, etc).

And the beneficiaries of that RFP would be the few who have unknowingly reserved a place on an 'invitation list' of sorts... like buying a Ferarri, where customers are available on an "invite only" basis?

Ryan from Ohio · Post by **Ryan from Ohio** » Sun Oct 22, 2006 10:39 am

Well you better figure it out, and make me a low powered version

I just paid for my new McIntosh radio

Im building that SQ system now...

subster87 · Post by **subster87** » Wed Oct 25, 2006 11:58 am

ok so as far as speaker positioning, tweeter will have to be set High on the doors about three inches below the window. The midbass can be mounted any where, and i would actually like to go three way if possible mounting the midbass in the factor location, and midbass to the left or possible 5 inches about the midbass, leaving midbass low, midrange in the middle of the door, and tweeter high. Can anyone give me a better understanding of components with those locations? i know subwoofers fairly well but components and proper location is all new to me. Any help would Be GREAT!

solacedagony · Post by **solacedagony** » Wed Oct 25, 2006 12:04 pm

You should probably start with a 2-way if you've never setup a system before. It's like trying to do tricks on a BMX bike without even being able to ride a bike.

subster87 · Post by **subster87** » Wed Oct 25, 2006 12:08 pm

Ive installed two sets of components jl Trs, and rockford 2 tweet punches. I just didnt know if i had them in the right spots for optimal sound. I have sealed my front doorts with about half a gallon of sludge, so the doors have no holes in them at all.

solacedagony wrote:You should probably start with a 2-way if you've never setup a system before. It's like trying to do tricks on a BMX bike without even being able to ride a bike.

solacedagony · Post by **solacedagony** » Wed Oct 25, 2006 12:14 pm

Ah ok. Sorry, I keep thinking active since that's what my head's been on for the past couple months :)
Read the SQ setup thing in the FAQ section. TONS of info in there.

subster87 · Post by **subster87** » Wed Oct 25, 2006 12:16 pm

Ok illl look into it and come out with a bunch of questions haha

solacedagony wrote:Ah ok. Sorry, I keep thinking active since that's what my head's been on for the past couple months :)
Read the SQ setup thing in the FAQ section. TONS of info in there.