Cant get in contact with RE audio?

Post by **GlassWolf** » Sun Mar 26, 2006 7:33 am

High Society wrote:lol, thats one reason why I dont go with JL and what not......Will that sub have a logo on it? And can you say the price? Maybe I should look for his old post? Does it use the 12 spoke basket?

here is the thread]http://www.caraudiocentral.net/forums/s ... =prototype[/url]

BigMack6933 · Post by **BigMack6933** » Sun Mar 26, 2006 9:24 am

I might put the Comps in a set of q logic kick panels because its gunna cost about 100+ in fiberglass to biuld a pair and the Qlogic ones looks really smooth and stock. Plus I have never biult kick panels.... and also I can put a nice set of 3way coaxils in the factory spot..... is it possible to run a set of components and a set of coaxils off a 2 channel amp?

Post by **GlassWolf** » Sun Mar 26, 2006 10:04 am

"coaxial 3-way" would be a triaxial, or "triax" for short. :)
If you put a set of separates and a set of triaxials on a 2 channel amp, you'll have a 2 ohm load, assuming all of the speakers are 4 ohms. That should work fine.

Personally I've found I prefer coaxials though, over triaxials. The two-way sets are much smoother without the harshness I tend to hear with the additional super-tweeter of a 3-way speaker. A good set of two-way coaxials will sound very good if they're positioned properly, and given ample power.

More ways isn't always better.

Justin from Detroit1 · Sun Mar 26, 2006 10:29 am

GlassWolf wrote:"coaxial 3-way" would be a triaxial, or "triax" for short. :)
If you put a set of separates and a set of triaxials on a 2 channel amp, you'll have a 2 ohm load, assuming all of the speakers are 4 ohms. That should work fine.
Personally I've found I prefer coaxials though, over triaxials. The two-way sets are much smoother without the harshness I tend to hear with the additional super-tweeter of a 3-way speaker. A good set of two-way coaxials will sound very good if they're positioned properly, and given ample power.
More ways isn't always better.

SO are you saying these Pioneer FIVE WAYS AREN'T GOOD? lol

BigMack6933 · Post by **BigMack6933** » Sun Mar 26, 2006 11:21 am

Would you guys start with the subs and sub amp or comps and comp amp?

BigMack6933 · Post by **BigMack6933** » Sun Mar 26, 2006 12:43 pm

to start I would only have the one set of components and would add the other set of Coax later on and if I did the two L5 8s I would buy one at a time

Post by **GlassWolf** » Sun Mar 26, 2006 2:17 pm

too complicated.
use two amps, one head unit, one good front set of separates, and two subs that aren't those shitty square subs.

then you have a good start :)

JeremyC · Post by **JeremyC** » Sun Mar 26, 2006 4:55 pm

GlassWolf wrote:too complicated.
use two amps, one head unit, one good front set of separates, and two subs that aren't those shitty square subs.
then you have a good start :)

joeyc · Post by **joeyc** » Sun Mar 26, 2006 5:20 pm

X2!!!!!

High Society · Post by **High Society** » Sun Mar 26, 2006 7:32 pm

I would pass on that cliff stuff. And the kicker Square subs. If you want to go kicker look into the compVr's. I'm sure for the price of the L5's and cliff subs you could do A LOT better. As for comps you seem like your on a budget, look into some CDT comps, there seems like theres deals everywhere on those.