Page 3 of 4
Posted: Sat Oct 21, 2006 3:10 pm
by Justin from Detroit1
When I was a dealer for Incriminator, the dealer cost on a 12" 187 was around $50. How the hell can they charge $35??
Posted: Sat Oct 21, 2006 3:34 pm
by audiobass10
Justin from Detroit wrote:When I was a dealer for Incriminator, the dealer cost on a 12" 187 was around $50. How the hell can they charge $35??
Where does it say they charge 35 bucks? There site was hacked recently..could have reflected changes in pricing. I cant even get on there right now.
Posted: Sat Oct 21, 2006 3:46 pm
by William from NOLA
Is their site working for you guys? I'm getting a "not authorized" message currently.
Posted: Sun Oct 22, 2006 10:35 am
by geolemon
GlassWolf wrote:any word on the statement 15" production?
Wish I could... Making changes, and focusing a bit more on the little sub, for better or worse. Really, we keep going back and forth, as we've got a "bigger and better" design that I'm pushing for, even though it's going to delay the release from the other option - a "release 1 / release 2" combination.
Due to some real support and enthusiasm here, I'm no doubt going to do a small "beta run" - essentially a RFP (request for prototype) that's perhaps 10 or 20 units under the guise of stress-testing for example - larger than your usual RFP.
And what might be cool with that is the "stealth" factor - usually those prototypes are mechanically exact, but with cosmetic details left out, so they could look slightly different (logo, plating, etc).
And the beneficiaries of that RFP would be the few who have unknowingly reserved a place on an 'invitation list' of sorts... like buying a Ferarri, where customers are available on an "invite only" basis?
Posted: Sun Oct 22, 2006 10:39 am
by Ryan from Ohio
Well you better figure it out, and make me a low powered version
I just paid for my new McIntosh radio
Im building that SQ system now...
Posted: Wed Oct 25, 2006 11:58 am
by subster87
ok so as far as speaker positioning, tweeter will have to be set High on the doors about three inches below the window. The midbass can be mounted any where, and i would actually like to go three way if possible mounting the midbass in the factor location, and midbass to the left or possible 5 inches about the midbass, leaving midbass low, midrange in the middle of the door, and tweeter high. Can anyone give me a better understanding of components with those locations? i know subwoofers fairly well but components and proper location is all new to me. Any help would Be GREAT!
Posted: Wed Oct 25, 2006 12:04 pm
by solacedagony
You should probably start with a 2-way if you've never setup a system before. It's like trying to do tricks on a BMX bike without even being able to ride a bike.
Posted: Wed Oct 25, 2006 12:08 pm
by subster87
Ive installed two sets of components jl Trs, and rockford 2 tweet punches. I just didnt know if i had them in the right spots for optimal sound. I have sealed my front doorts with about half a gallon of sludge, so the doors have no holes in them at all.
solacedagony wrote:You should probably start with a 2-way if you've never setup a system before. It's like trying to do tricks on a BMX bike without even being able to ride a bike.
Posted: Wed Oct 25, 2006 12:14 pm
by solacedagony
Ah ok. Sorry, I keep thinking active since that's what my head's been on for the past couple months :)
Read the SQ setup thing in the FAQ section. TONS of info in there.
Posted: Wed Oct 25, 2006 12:16 pm
by subster87
Ok illl look into it and come out with a bunch of questions haha
solacedagony wrote:Ah ok. Sorry, I keep thinking active since that's what my head's been on for the past couple months :)
Read the SQ setup thing in the FAQ section. TONS of info in there.