Attention all members!
Have a cool ride? Then show it off on our website! All vehicles welcome!

Carpet Application

Anything not related or doesnt fit another Forum.
solacedagony
Master of My Domain
Posts: 2171
Joined: Mon Nov 29, 2004 9:34 am
Location: Phillipsburg, NJ
Contact:

Carpet Application

Post by solacedagony »

This will be the first box that I actually carpet. I bought some Super77 3M spray on adhesive. Now, is there a certain pattern you should use to box, or place to start from? Any tips or helpful hints are appreciated.
cargodz
Master of My Domain
Posts: 4771
Joined: Tue Jul 04, 2006 7:21 am
Location: NW Ohio
Contact:

Post by cargodz »

with this being your first, allow each side to dry before moving to the next, and make sure you have the application covered completely or it may wrinkle up later, be liberal with the adhesive, but don't saturate it either.
Kinda like paint...Too little= not enough coverage, Too much and you'll be cleaning it up or worse.
Hope this helps & Good Luck :)

P.S. Don't try and cut the holes first, not saying you will, but I've seen it done and it's bad.
& I always start from the bottom, but that's just me.
-Michael
http://www.teamcargodzinc.com :thumbsup
Hear It, See It, Feel It, Punch It!
And Proud Sponsor of
Team Wolf Pack Audio
Authorized Dealer
joeyc
Master of My Domain
Posts: 1703
Joined: Sun Dec 11, 2005 1:15 pm
Location: Tulsa

Post by joeyc »

check the faq section, I think that carpet is "covered" there....pun unintentionally intended :p
Morel Elate 3-ways ran by a Genesis Series III Dual-mono, Morel Ultimo ran by an Autotek mm3000.1, Alpine DVA-9861

JC's Customs
For all your stereo wants.......
Ryan from Ohio
Posts: 13308
Joined: Fri Mar 17, 2000 12:00 pm
Contact:

Post by Ryan from Ohio »

Check the FAQ

:surprised
-Ryan
www.caraudiocentral.net - Your #1 Car Audio Resource on the Net!
solacedagony
Master of My Domain
Posts: 2171
Joined: Mon Nov 29, 2004 9:34 am
Location: Phillipsburg, NJ
Contact:

Post by solacedagony »

Oops sowwy! Shoulda checked the FAQ page first.
joeyc
Master of My Domain
Posts: 1703
Joined: Sun Dec 11, 2005 1:15 pm
Location: Tulsa

Post by joeyc »

Just don't do it again, OR ELSE....RYAN WILL BAN YOU!!! lol
Morel Elate 3-ways ran by a Genesis Series III Dual-mono, Morel Ultimo ran by an Autotek mm3000.1, Alpine DVA-9861

JC's Customs
For all your stereo wants.......
solacedagony
Master of My Domain
Posts: 2171
Joined: Mon Nov 29, 2004 9:34 am
Location: Phillipsburg, NJ
Contact:

Post by solacedagony »

Haha, I hope you've learned your lesson! *pointing finger* haha
Ryan from Ohio
Posts: 13308
Joined: Fri Mar 17, 2000 12:00 pm
Contact:

Post by Ryan from Ohio »

No banning of good members now.

:thumbsup
-Ryan
www.caraudiocentral.net - Your #1 Car Audio Resource on the Net!
User avatar
jonnyb
Senior Member
Posts: 557
Joined: Fri Oct 08, 2004 4:00 am
Location: The Awesome Lands

Post by jonnyb »

a few tips though:
take your time. when you go to cut something, look at it like 5 times to be sure it is going to look good. also get a pack of those 100 single edge razor blades, and use a new one if you think one is getting dull. the sharper the blade, the better the cut.
solacedagony
Master of My Domain
Posts: 2171
Joined: Mon Nov 29, 2004 9:34 am
Location: Phillipsburg, NJ
Contact:

Post by solacedagony »

Thanks man, I'm going to have to get some replacements for my utility knife.
Post Reply