Attention all members!
Have a cool ride? Then show it off on our website! All vehicles welcome!
Have a cool ride? Then show it off on our website! All vehicles welcome!
Yet Another New Sub Line?
-
mikechec9
- Senior Member
- Posts: 144
- Joined: Sat May 14, 2005 5:53 pm
- Location: Chicago/Atlanta
- Contact:
Yet Another New Sub Line?
http://www.diymobileaudio.com/shop/prod ... 3453fe660d
looks promising.
*Edit* Save the "Maximum thermal powerhandling"
looks promising.
*Edit* Save the "Maximum thermal powerhandling"
It's interesting, very cool looking...
23mm isn't necessarily huge in today's world.
Motor curve looks pretty decently flattened- a bit surprised that they would have such a parabolic suspension curve, since it takes BOTH to create actually linear cone motion...
Without that, there's still going to be some semblence of intermodulation distortion- hopefully only half of what you'd get from a standard driver, since only half the motion system would be contributing to it, if you will.
$600 seems pretty steep.
I'm curious what motor technology they use - and curious if the Focal "multi-mag" style was built in for a reason... Focal uses it for heritage essentially at this point, having pioneered it at a time when large ring magnets weren't commonly available - but small ones were.
...it's possible it's an underhung driver, but by virtue of the outside appearance of the top plate, it's unlikely. Could be machined to a thicker inside gap like some of the TC Sounds drivers commonly are.
Curious!
23mm isn't necessarily huge in today's world.
Motor curve looks pretty decently flattened- a bit surprised that they would have such a parabolic suspension curve, since it takes BOTH to create actually linear cone motion...
Without that, there's still going to be some semblence of intermodulation distortion- hopefully only half of what you'd get from a standard driver, since only half the motion system would be contributing to it, if you will.
$600 seems pretty steep.
I'm curious what motor technology they use - and curious if the Focal "multi-mag" style was built in for a reason... Focal uses it for heritage essentially at this point, having pioneered it at a time when large ring magnets weren't commonly available - but small ones were.
...it's possible it's an underhung driver, but by virtue of the outside appearance of the top plate, it's unlikely. Could be machined to a thicker inside gap like some of the TC Sounds drivers commonly are.
Curious!
-
Ryan from Ohio
- Posts: 13308
- Joined: Fri Mar 17, 2000 12:00 pm
- Contact:
I have yet to see where it says $600 bossgeolemon wrote: $600 seems pretty steep.
$150 I see though and a normal price tag of $219...
1000 WRMS is pretty steep though. Cost a fortune to run that baby!
-Ryan
www.caraudiocentral.net - Your #1 Car Audio Resource on the Net!
www.caraudiocentral.net - Your #1 Car Audio Resource on the Net!
Hell I have half a mind..................
that's it...I just have half a mind...do you know where the other half is?
I might purchase one just to try out in my car, although I am also getting the betteraudio one that Geolemon is designing.
that's it...I just have half a mind...do you know where the other half is?
I might purchase one just to try out in my car, although I am also getting the betteraudio one that Geolemon is designing.
IASCA Certified SQ Judge
USACi Certified SQ Judge
MECA Certified SQ Judge
2010 USACi Spring Break Jam Modified SQ Champion
Moderator for https://www.facebook.com/groups/524841581331183/
CVD Audio Sales and Acquisitions Team
http://www.cvdaudio.com
USACi Certified SQ Judge
MECA Certified SQ Judge
2010 USACi Spring Break Jam Modified SQ Champion
Moderator for https://www.facebook.com/groups/524841581331183/
CVD Audio Sales and Acquisitions Team
http://www.cvdaudio.com
-
Justin from Detroit1
- Junior Member
- Posts: 0
- Joined: Wed Dec 31, 1969 6:00 pm
- Location: Detroit
I think it's XBL^2. The DIYMA 7" midwoofer is going to be, I'd guess NPDang decided to go the same route with his sub.geolemon wrote:I'm curious what motor technology they use - and curious if the Focal "multi-mag" style was built in for a reason... Focal uses it for heritage essentially at this point, having pioneered it at a time when large ring magnets weren't commonly available - but small ones were.
...it's possible it's an underhung driver, but by virtue of the outside appearance of the top plate, it's unlikely. Could be machined to a thicker inside gap like some of the TC Sounds drivers commonly are.
Curious!
-
sinister audio
- Master of My Domain
- Posts: 2562
- Joined: Sat Mar 19, 2005 9:00 am
- Location: Watertown, South Dakota
- Contact:
-
mikechec9
- Senior Member
- Posts: 144
- Joined: Sat May 14, 2005 5:53 pm
- Location: Chicago/Atlanta
- Contact:
There's the "C" word. Thanks. Not sure how I missed it, but managed to see "Maximum." :happy055:Bwcad1 wrote:Maximum thermal powerhandling: 1000 watts continuous power
its under the specs part on the page!
Anyway, I'm curious about the multi-magnet design also. I recall one brand that popped out of nowhere last year (and dissapeared just as quickly) that used the same structure. For focal's utopia home drivers, the "flower" design was supposed to produce a more consistent and efficient field yielding increased damping and tonal balance. But that was way back in college, so i agree it's likely just a matter of tradition now. Sounded like BS then too, but...
Sure would be nice if someone here could guine up and nab one of these. Thinking of a driver for Wifey's neon.

