Hey guys, sorry if this question sounds stupid but I'm new to everything.
What's the difference between 2 ohm and 4 ohm.
I plan on getting a 4 channel amp soon and wiring it to my head unit and subwoofer.
Should I use 2 ohm or 4 ohm? Thanks
Attention all members!
Have a cool ride? Then show it off on our website! All vehicles welcome!
Have a cool ride? Then show it off on our website! All vehicles welcome!
Ohm Question
-
GlassWolf
- Master of My Domain
- Posts: 6725
- Joined: Thu Oct 07, 2004 4:00 am
- Location: Columbia, SC
- Contact:
read http://www.bcae1.com
ohms are a measure of resistance or impedance.
4 ohms is twice the impedance of 2 ohms.
ohms are a measure of resistance or impedance.
4 ohms is twice the impedance of 2 ohms.
GlassWolf (aka KikiTheCat)
moderator-administrator
How it matters to you is that 2 ohms is less "resistance" than 4 ohms.
Specifically, it is "less resistance" against current flowing through a circuit.
The lower the impedence (or resistance), the more current will flow.
And, the more current flows through any electronics, the more heat is produced.
What makes a fuse blow? Too much current flowing through it, right?
Why does it blow? The element melts - heat.
This is important in car audio, because you don't want your amp internals to melt, by hooking up too low of an impedence to it. It's not just fuses that melt.
...which is why amps are rated as being "stable down to..." a specific impedence. 2 ohms, 1 ohm, whatever. You don't want to hook up a lower impedence than what it's been designed for.
Speakers come in many impedences (plus, you can wire them in combinations to either double, or halve the impedence for each combination of two you connect) so that you can wire them to the proper impedence you need, given whatever amp it is you have.
Specifically, it is "less resistance" against current flowing through a circuit.
The lower the impedence (or resistance), the more current will flow.
And, the more current flows through any electronics, the more heat is produced.
What makes a fuse blow? Too much current flowing through it, right?
Why does it blow? The element melts - heat.
This is important in car audio, because you don't want your amp internals to melt, by hooking up too low of an impedence to it. It's not just fuses that melt.
...which is why amps are rated as being "stable down to..." a specific impedence. 2 ohms, 1 ohm, whatever. You don't want to hook up a lower impedence than what it's been designed for.
Speakers come in many impedences (plus, you can wire them in combinations to either double, or halve the impedence for each combination of two you connect) so that you can wire them to the proper impedence you need, given whatever amp it is you have.
-
GlassWolf
- Master of My Domain
- Posts: 6725
- Joined: Thu Oct 07, 2004 4:00 am
- Location: Columbia, SC
- Contact:
the trick is matching the speakers you choose to the right amplifier..
that will depend on if the amplifier will be bridged or not, or if it's mono, how many speakers each channel will drive, how they're wired together, etc.
What may be easier is to pick out your speakers, and tell us the specs of them.
Then give us a budget to work with and we can suggest both good amplifiers, and how to connect them.
that will depend on if the amplifier will be bridged or not, or if it's mono, how many speakers each channel will drive, how they're wired together, etc.
What may be easier is to pick out your speakers, and tell us the specs of them.
Then give us a budget to work with and we can suggest both good amplifiers, and how to connect them.
GlassWolf (aka KikiTheCat)
moderator-administrator
-
albino