cut out

Tim · Post by **Tim** » Sat Mar 14, 2009 5:37 pm

I had the same problem, try this when the music stops go back and apply gentle pressure on the cone of the sub, as I said gentle pressure barely pushing it in and see if the music comes back on. I had it happen and it was bad coil(s). Try it and see.

Try not to flame me for this method as I know it is not the best way but it worked for me.

Tim

JeremyC · Post by **JeremyC** » Sat Mar 14, 2009 5:44 pm

Yeah I'm not going to lie tim, I have done that too.

But there is a better way. Disconnect the amp and connect an ohm meter to the wires that would normally connect to the amp. Now go back and slowly move the sub. Its should go from your DC impedance and rise gradually. If it does something screwy (goes to open or zero ohms you have a problem)

drdoom23 · Post by **drdoom23** » Sat Mar 14, 2009 5:54 pm

I had this issue before with a cheap amo the gain may be set to high and its going into protect mode or its just over heating, weera it located? Is it able to stay cool?

drdoom23 · Post by **drdoom23** » Sat Mar 14, 2009 6:01 pm

So this will test for a bad coil??and r u talkin the speaker wire that connects to the amp

JeremyC wrote:Yeah I'm not going to lie tim, I have done that too.
But there is a better way. Disconnect the amp and connect an ohm meter to the wires that would normally connect to the amp. Now go back and slowly move the sub. Its should go from your DC impedance and rise gradually. If it does something screwy (goes to open or zero ohms you have a problem)

Sat Mar 14, 2009 7:46 pm

sounds like you have your gain set too high, try turning it down some and see how it works then.

Ryan from Ohio · Post by **Ryan from Ohio** » Sat Mar 14, 2009 8:34 pm

If the gains set about half way I dont think thats the problem.

How hot does the amp feel when it starts cutting out? If its hot, then you can guess its a thermal issue. Could be you have your subs wired to low...

Tim · Post by **Tim** » Sat Mar 14, 2009 8:42 pm

JeremyC wrote:Yeah I'm not going to lie tim, I have done that too.
But there is a better way. Disconnect the amp and connect an ohm meter to the wires that would normally connect to the amp. Now go back and slowly move the sub. Its should go from your DC impedance and rise gradually. If it does something screwy (goes to open or zero ohms you have a problem)

Yeah I knew there was a better way. I hate to admit I've done that, but at the time it was my only test as I didnt have my meter with me. I think this question was asked, but for clarification you are talking about the sub wires right??

Tim

JeremyC · Post by **JeremyC** » Sun Mar 15, 2009 5:20 am

drdoom23 wrote:So this will test for a bad coil??and r u talkin the speaker wire that connects to the amp

Yes and yes

drdoom23 · Post by **drdoom23** » Sun Mar 15, 2009 8:29 am

JeremyC wrote:Yes and yes

cool so i can just un hook the speaker wire from the amp and hook my meter on those wires and it will tell me if i have a fried coil sweetya last time i un hooked the sub from the box and tested and man was that a pain in the ass

drdoom23 · Post by **drdoom23** » Sun Mar 15, 2009 8:31 am

Chris from Washington wrote:sounds like you have your gain set too high, try turning it down some and see how it works then.

thats what i thought see i had this same issue with a cheaper amp i had and i had to reset everything and since since i sold my old set up to my brother he's had no issue whatsoever so im thinking the gain or the amp just isnt in a good place to get the air to help cool it or both