Attention all members!
Have a cool ride? Then show it off on our website! All vehicles welcome!

2000 buick century

Post a reply

Confirmation code
Enter the code exactly as it appears. All letters are case insensitive.
Smilies
:awesome: :argh :ditto :inout :words :bow :cheers: :bigwink: :fing02: :sad017: :scorp: :o :D ;) :p :unwell028 :tongue017 :thumbsup :surprised :sm29: :angry011: :angry015: :angry012: :nono: :angry010: :nono :banghead :mad: :dif :angry :CRZ_13: :eek: :confused: :confused0 :confused :( :sad: :cool: :dance :mecry: :jesterlol :embarrass :flame: :doh :evil019: :evil001: :rolleyes: :sub:
View more smilies
BBCode is ON
[img] is ON
[url] is ON
Smilies are ON
Topic review
   

Expand view Topic review: 2000 buick century

by glassdonk75 » Thu Jun 09, 2005 5:26 am

Basstronics I found a place where the wiring harness comes through that big rubber grommet comes out from around the wire then the rubber boot I cut out a spot and went through with my 4 guage. Thanks alot. My nexr question is I have 2 audiobahn AW120T 12" subs and need a good amp to push any suggestions. They are rated 500 rms and 1000 peak.

by Ryan from Ohio » Wed Jun 08, 2005 2:07 pm

The tape will wear just like the wires shielding... :p

I have a 97 century so I know exactly what your up againt. THis car has NO PLACE to run the power wire through, you have to make your own.

Best place...

Pull the carpet away where the passengers feet are. You will see where the factory wiring comes thru the firewall. Go about 3-4" ABOVE that and about 2-3" OVER from it. This should put you right below the Alternator.

I made the mistake of drilling to low and went through a few wires and I had to splice up the factory wiring...wasnt to happy about that. Learn from my mistake and take that advice on where to drill... Double check also ;)

by William from NOLA » Wed Jun 08, 2005 1:17 pm

Yea, I almost said get a grommet, but that means he'd have to go out and get one which is only a few cents, but you'd spend more in gas going out there than you would if you used tape. heh

by dmeyer07 » Wed Jun 08, 2005 1:07 pm

Well thats what the grommet does for you, it acts as a barrier between the firewall and the wire so it doesn't get torn up. Plus it creates a nice waterproof seal so nothing will enter through that hole.

PRO GROMMET
The ultimate professional sealing grommet! Prevents water and wind noise from entering the interior cabin.
PG34: 1/0 gauge - 1” O.D.
PG12: 4 gauge - 7/8” O.D.
PG38: 8 gauge - 5/8” O.D

Looks Like This:
Image

by William from NOLA » Wed Jun 08, 2005 10:11 am

You will want to tape up the hole so that it doesn't tear up the power cable (if you make your own hole that is).

by glassdonk75 » Wed Jun 08, 2005 10:05 am

thanks I was looking so I will just drill a hole for it.

by dmeyer07 » Wed Jun 08, 2005 10:02 am

Um if your 100% sure that there is no where at all for the wire to be run, then drill your own hole. But make sure your clear of any wires,etc on BOTH sides first. Also make sure you have a nice sharp bit! Then just place a groment in there and slide your wire throguh.
look harder though im sure theres an opening somewhere in that firewall that you can squeeze a power wire through :) .

2000 buick century

by glassdonk75 » Wed Jun 08, 2005 9:59 am

I am installing my system in a 2000 buick century and need a little assistance. I was looking for a place to run my power cable from the battery but cant find anywhere to go through the firewall. Any suggestions?

Top