Page 2 of 3
Posted: Wed Apr 25, 2007 9:06 am
by swimmerdude
cargodz wrote:That does create and usually is the largest problem... Money
To truly get the best for your dollar, you still need to save more than most are willing to... Most have it burning a hole in their pocket and can't wait to spend it... My advise for anyone that uses method is to buy a peice at a time... you get better equipment from the word go and then have an idea of what you need to save up for next, so you're not as likely to blow it on lesser equipment than what you really want... Just my honest opinion.
+1
I would go this route because you will be much happier down the road. Actually, I did go this route when I purchased my Elevation DX1500.1, then a month or so later, i purchased my Elevation Execution. I was really happy with what i did. Once everyone gets a system, they always want to upgrade. By going with something that is only what you can afford now, you will really want to upgrade soon. So you are going to end up spending more money because you wont sell your stuff for the same price you bought it for.
Posted: Wed Apr 25, 2007 12:44 pm
by hartman
i can just buy the fusion package and upgrade it later when i get money. or i could w8 till i get more money and buy a system i dont know yet.
Posted: Wed Apr 25, 2007 5:01 pm
by Jonathan
You'll lose soooo much money doing the upgrade it later option.
Posted: Wed Apr 25, 2007 5:19 pm
by brownbob06
I did, it doesn't say DVC on the subs, and it says 4 ohm Impedance...so wouldn't that be 160W?
Posted: Wed Apr 25, 2007 5:50 pm
by smoker
problem solved, fusion nvsw12 and an ssl 1500 watt monoblock amp, kick ass sub, solid amp, and im giving him a sealed box i have that i built a while back that is put together like a brick shithouse, ......its gonna pound. my favorite high end sub and my favorite middle of the road amplifier.....
Posted: Thu Apr 26, 2007 12:12 am
by cargodz
I kinda figured you'd figure out somethin for him Terry :) ... That system will definately do the job.
Posted: Thu Apr 26, 2007 12:17 am
by cargodz
brownbob06 wrote:I did, it doesn't say DVC on the subs, and it says 4 ohm Impedance...so wouldn't that be 160W?
2 single 4ohm voice coils wired in parallel would be a 2 ohm load not a 4 ohm load.
Posted: Thu Apr 26, 2007 7:29 am
by brownbob06
but it just says "impedance-4 ohms"
I know DVC 4 Ohm is 2 ohm...but that description just isn't clear at all...o well, no big deal.
Posted: Thu Apr 26, 2007 7:31 am
by brownbob06
but it just says "impedance-4 ohms"
I know DVC 4 Ohm is 2 ohm...but that description just isn't clear at all...o well, no big deal.
Posted: Thu Apr 26, 2007 12:53 pm
by cargodz
brownbob06 wrote:but it just says "impedance-4 ohms"
I know DVC 4 Ohm is 2 ohm...but that description just isn't clear at all.
The description is perfectly clear and will be to you too once you've been doin this for a while.
If you have 2) single 4 ohm voice coils and wire them in parallel, then it's the same as having 1) 4 ohm Dual voice sub wired parallel = 2 ohm load...
If you had 2) 4 ohm Dual Voice coil subs wired in parallel it would equal a 1ohm load. :)
JL has a pretty good tutorial for ya on wiring up subs.... you can find it here:
http://mobile.jlaudio.com/support_pages.php?page_id=145