Attention all members!
Have a cool ride? Then show it off on our website! All vehicles welcome!

MA Audio Midbass through my A/D/S pp amp

Post a reply

Confirmation code
Enter the code exactly as it appears. All letters are case insensitive.
Smilies
:awesome: :argh :ditto :inout :words :bow :cheers: :bigwink: :fing02: :sad017: :scorp: :o :D ;) :p :unwell028 :tongue017 :thumbsup :surprised :sm29: :angry011: :angry015: :angry012: :nono: :angry010: :nono :banghead :mad: :dif :angry :CRZ_13: :eek: :confused: :confused0 :confused :( :sad: :cool: :dance :mecry: :jesterlol :embarrass :flame: :doh :evil019: :evil001: :rolleyes: :sub:
View more smilies
BBCode is ON
[img] is ON
[url] is ON
Smilies are ON
Topic review
   

Expand view Topic review: MA Audio Midbass through my A/D/S pp amp

by solacedagony » Thu Sep 14, 2006 10:20 am

Let me know how that industrial strength velcro does with holding the pod in place. When do you plan on doing this project? What crossover points/slopes are you planning on?
JeremyC wrote:Be carefull with that. Most mids are designed to be ran IB, so they might not like it. I know JoeyC was having some problems with his mids, so he cut out the back of his kick panel where it sealed up tight to the floor and it helped a TON.
I was going to post that earlier, but I forgot. You should def look and see what is recommended. Also, I would do a search for whatever driver (Specifically if it's Seas, Peerless, or Dayton) you decide to run on diymobileaudio.com because a lot of those guys are running those raw drivers.

by CaptainPioneer » Thu Sep 14, 2006 8:48 am

well then what i will do is first go with sealed and if it doesnt sound right... i will cut out the mold at the bottom... The cool thing with these molds is that they wont be fastend down to the floor via screws... Im going to make them removeable by using Industrial strength velcro all around the edges :) And i believe that i am going to just carpet over the fiberglass with some matching colors of the interior

by JeremyC » Wed Sep 13, 2006 4:17 pm

CaptainPioneer wrote:Sealed
Be carefull with that. Most mids are designed to be ran IB, so they might not like it. I know JoeyC was having some problems with his mids, so he cut out the back of his kick panel where it sealed up tight to the floor and it helped a TON.

by solacedagony » Wed Sep 13, 2006 10:00 am

I would just check what volume they should be in for at least a flat reponse.

by CaptainPioneer » Wed Sep 13, 2006 9:21 am

Sealed

by solacedagony » Wed Sep 13, 2006 9:04 am

I would think that'll be enough room for cooling. You planning on running your pods sealed or IB?

by CaptainPioneer » Wed Sep 13, 2006 8:21 am

Yea but my main concern is keeping my car nice and spacious while also giving that extra punch up front... i think that I will go with the 7" it fits perfectly within my power ratings and thats the orignial size i wantted to go with in the first place... plus its a bit cheaper... :) Now when i put these little buggers in a fiberglass pod how much space should i give it from the magnet to the bottom of the mold? I was thinking around an inch and since they will be angled appropriately i think there will be a bit more space underneath them as well?

by solacedagony » Wed Sep 13, 2006 3:21 am

Remember that it's midBASS so the amount of air that your speakers are moving is going to start to matter. So if you could fit an 8" for your midbass, the better.

by CaptainPioneer » Tue Sep 12, 2006 6:37 pm

could u see any problems going with a 6 or 7 inch? i was thinking the 6 inch maybe at least the 7 inch but I think the 8 inch might be a lil too big in the kick pannel

by solacedagony » Tue Sep 12, 2006 4:28 pm

:) :horse

Top