Attention all members!
Have a cool ride? Then show it off on our website! All vehicles welcome!

speaker wiring

Post a reply

Confirmation code
Enter the code exactly as it appears. All letters are case insensitive.
Smilies
:awesome: :argh :ditto :inout :words :bow :cheers: :bigwink: :fing02: :sad017: :scorp: :o :D ;) :p :unwell028 :tongue017 :thumbsup :surprised :sm29: :angry011: :angry015: :angry012: :nono: :angry010: :nono :banghead :mad: :dif :angry :CRZ_13: :eek: :confused: :confused0 :confused :( :sad: :cool: :dance :mecry: :jesterlol :embarrass :flame: :doh :evil019: :evil001: :rolleyes: :sub:
View more smilies
BBCode is ON
[img] is ON
[url] is ON
Smilies are ON
Topic review
   

Expand view Topic review: speaker wiring

by cheapaudio » Wed Jan 16, 2008 9:19 am

ok, im buying the Autotek MM 100.4 to run my components,, now that i can use all the inputs on the crossover, since you can just hook up the woofer input at 4 ohms, would i now run both tweeter and woofer inputs at 2 ohms stereo or run all 4 channels at 4 ohms stereo? or would that hurt the tweeters not being in HP mode, or would it best to stick with the 2 channel amp

by cargodz » Wed Jan 09, 2008 3:38 pm

That's what the jumper is for... It's just a small piece of wire that runs from one to the other.

by cheapaudio » Wed Jan 09, 2008 11:58 am

does the jumper work automatically, becuz theres no switch, the diagram for one amp shows just hookin one channel to the wooofer input and nuthin to the tweeter input

by Bwcad1 » Wed Jan 09, 2008 11:39 am

Jonathan wrote:I can't remember exactly but most bi-amp crossovers have a jumper that lets you choose bi-amp or single input. Regardless if it's only bi amp, you can run two sets of wires from the same channel of the amp, one to the woofer input and one to the tweeter input.
x2 mang

by Jonathan » Wed Jan 09, 2008 11:30 am

I can't remember exactly but most bi-amp crossovers have a jumper that lets you choose bi-amp or single input. Regardless if it's only bi amp, you can run two sets of wires from the same channel of the amp, one to the woofer input and one to the tweeter input.

by cheapaudio » Wed Jan 09, 2008 11:09 am

i see the cross overs they have 2 channel out puts one for the woofer and one for the tweeter, but on the input there are 2 channels one for the tweeter and one for the woofer but im only runnin one channel from my amp to the cross over, would i just hook the channel to the woofer input on the cross over or split it and run 2 positives one for tweeter and one for woofer and then 2 negatives from one channel of my amp , but then wouldnt that effect the ohm load?

by Bwcad1 » Wed Jan 09, 2008 11:01 am

yes you do see the boxes with gold screw terminals in them? and looks like big copper coils? those are your crossovers. read the manual this should explain most of it

by cheapaudio » Wed Jan 09, 2008 10:56 am

i have the Alpine SPX-17REF components, i dont think its a passive crossover, it says external crossover with bi amp capability

by Bwcad1 » Wed Jan 09, 2008 10:12 am

what set do you have? did it come with a passive cross over? if so wire one set of wires to the input on the passive cross over. and then wire the tweeter and mid to the corrosponding spots on the crossover.

speaker wiring

by cheapaudio » Wed Jan 09, 2008 9:26 am

hookin up my first set of components, i have one 2 channel amp, the cross over has a woofer and tweeter speaker wire inputs,, do i hook up both or just one channel to the woofer input? the diagram shows an amp hooked to the tweeters and an amp to the woofer?

Top